Stepper Servo

SCS86 digital display stepper servo driver

SCS86 digital display stepper servo driverBased on the new 32-bit DSP platform, provided with vector control technology and servo demodulation function internally, SCS86 stepper servo driver enables t

SCS86 digital display stepper servo driver

Based on the new 32-bit DSP platform, provided with vector control technology and servo demodulation function internally, SCS86 stepper servo driver enables the stepper servo system to feature low noise, low heating.S86 is used to drive two-phase closed-loop stepper motors base below 86mm.

Typical applications: welding machine, wire-stripping machine, labeling machine,carving machine, electronic assembly equipment etc.

Product Specification

Drive featuresOperating instructions
Signal interfacePUL+and PUL-for the positive and negative ends of the control pulse signal;DIR+and DIR-for the positive and negative end of the direction signal;ENA is the enable signal;IN2 is undefined,COM+is the common correct,COM-is the common negative;BRK-is the brake output signal,ALM-is the alarm output signal;PEND-for the position output signal.
 Encoder interface EB+and EB-are the encoder B direction signals;EA+and EA-are encoder A direction signals;VCC and GND are the encoder power interfaces
Motor interfaceA+,A-,B+,B-are stepper servo motor winding interfaces,need to be connected with the motor identification color,can not be exchanged.PE grounding wire,NC suspended not connected.
Power portAC and AC are common input terminals for AC and DC power supplies.DS86 operating voltage range is 18-80VAC or 24-100VDC,power supply is greater than 200W.PE ground cable,NC suspended without connection

 

The parameters of the drive can be set from PA-00 to PA-40

Steps/revolutionsParameter namesScope  Default
  values
Instructions
00Control   mode[0,2] 10:open loop operation     1:servo mode 1
2:Servo   Mode   two
01Subdiyision[200,65535] 1600The number of pulses required for the motor to run one turn
02Maximum current[100,7000] 7000When matching different motors,first
confirm whether the maximum current is
appropriate before connecting the motor
03Percentage of Base current[1,100] 50
04Encoder resolution[500,65535] 4000The resolution of a 1000-wire encoder is 4000
05Position error alarm threshold[100,65535] 4000Set the drive tracking error alarm threshold
06Reverse direction[0,1] 00:Default direction
1:The motor running direction is reversed
07Instruction filtering[1,512] 128Time lag =set point x 50us,parameter
set to 1 when interpolating motion
08Pulse    Mode[0,1] 00:Pulse+direction
1:Double pulse
09Pulse effective edge[1,512] 1280:Rising edge effective
1:The falling edge is effectiv
10Enable level[0,1] 00:Normally open
1:Normally closed

 

SCS86 Connections

DS86

 

Product Dimensions

DS86 Dimensions

 

       Common problems and  countermeasures
PhenomenaPossible situationSolutions
  Motor not turningThe power light does not workCheck the power supply circuit for normal power supply
The motor locks the shaft but does not turnThe pulse signal is weak and the signal current is increased to 7-16mA
 Too little speedPick the right subdivision
 Drive protectedPower back on
Enable the signal problemPull the enable signal high or not
 Incorrect command pulseCheck the upper computer for pulse output
Motor steering error Motor steering in reverseChange the motor wiring sequence or adjust the direction of instructions
 There is a break in the motor lineCheck the wires for poor contact
 The motor has only one directionPulse mode is wrong or DIR port is damaged
Alarm indicator light Motor wire is incorrectly connectedCheck the wiring
 Voltage is too high or too lowCheck the power supply
 Damaged motor or driveReplace the motor or drive
Wrong location or speed Signal interferenceEliminate interference and ground reliably
 Incorrect command inputCheck the upper computer instructions to ensure the correct output
 The pulse per revolution is set
incorrectly
Check dip switch status and connect correctly
 Motor drop sterCheck whether the command speed is too large and the motor selection is small
The driver terminal is
burned out
 Short circuit between terminalsCheck the power supply polarity or external short circuit
 There is too much internal
resistance between terminals
Check whether excess solder has been added to the wire and wire connection
to form tin clumps
  Motor gridlock  The acceleration and deceleration
time is too short
Reduce the command acceleration or increase the driver filter parameter
 Too little motor torqueChoose a high-torque motor
 Heavy loadCheck the weight and quality of the load and adjust the mechanical structure
 Too little currentCheck the dip switch to increase the drive output current

 

FAQ

Can we accept samples customized?

No problem for samples order, and welcome your testing before your big order.

 

OEM and ODM are available?

Yes, we accept customized products

 

Can I get a lower price if I order large quantities?

Yes, Cheaper prices with bigger size orders, please contact us and we will give you a quatation.


热门推荐